owner’s manual
SCT-530
HIGH-SPEED DUBBING STEREO CASSETTE DECK
PRB1199A.En.01.09.DOC
1
9/2/99, 9:22 PM
IMPORTANT SAFETY INSTRUCTIONS
Careful attention is devoted to quality standards in the manufacture of your cassette deck, and safety is a
major factor in its design. However, safety is also your responsibility.
This cassette deck is made and tested to
meet exacting safety standards. It meets
both UL and FCC requirements.
This section lists important information that will help you properly use and enjoy your cassette deck and
accessories. Read all the included safety and operating instructions before using your cassette deck, follow
them closely, and retain them for future reference.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for cleaning.
Do not use liquid or aerosol cleaners.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
Attachments — Do not use attachments/accessories not recommended by the product manufacturer, as
they might create a hazard.
Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
THE COVER. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
Follow the manufacturer’s instructions for mounting, and use a recommended mounting accessory.
Carts — Move the product on a cart carefully. Quick stops, excessive force, and
uneven surfaces may cause the product/cart to overturn.
This symbol is intended to
alert you to the presence of
dangerous voltage inside
the product that can cause
shock. Do not open the
product’s case.
Ventilation — Slots and openings in the cabinet provide ventilation, ensure
reliable operation, and protect from overheating. Do not block or cover these
openings, and do not place the product on a bed, sofa, rug, or other similar
surface. Do not place the product in a built-in bookcase or rack unless it provides
proper ventilation as specified by the manufacturer.
Power Sources — Operate this product using only the power source indicated on its marking label. If
you are not sure of your home’s power type, consult your product dealer or local power company.
Polarization — This product is equipped with a polarized AC line plug (a plug having one blade wider
than the other). This plug will fit in the power outlet only one way. This is a safety feature. If you cannot
insert the plug fully into the outlet, try reversing the plug. If the plug still doesn’t fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If you
need an extension, use a polarized cord.
This symbol is intended to
alert you to important
operating and maintenance
instructions in this owner’s
manual.
Power-Cord Protection — Route power-supply cords so they are not likely to be walked on or pinched
by items placed on or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
Lightning — For added protection for this product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and power-line surges.
WARNING: TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THISAPPLIANCE TO
RAIN OR MOISTURE.
Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles, as this
can result in a risk of fire or electric shock.
Objects and Liquids — Never push objects of any kind into this product through openings, as they may
touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Servicing — Do not attempt to service this product yourself, as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
This cassette deck complies with the limits for a Class B
digital device as specified in Part 15 of FCC Rules. These
limits provide reasonable protection against radio and TV
interference in a residential area. However, your equipment
might cause radio or TV interference even when it is
operating properly. To eliminate interference, you can try
one or more of the following corrective measures:
Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the product.
If the product has been exposed to rain or water.
•
•
Reorient or relocate the receiving antenna.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
Increase the distance between the cassette deck and the
radio or TV
•
Use outlets on different electrical circuits for the
cassette deck and the radio or TV
•
•
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance.
Consult your local Radio Shack store or an experienced
radio/TV technician if the problem still exists.
Replacement Parts — When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or having the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check — Upon completion of service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended by
the manufacturer.
Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
3
PRB1199A.En.01.09.DOC
3
9/2/99, 9:22 PM
CONTENTS
Connections ............................................................................................................................. 5
Connecting the Recording and Playback Cables ......................................................................................... 5
Connecting Power ....................................................................................................................................... 5
Basic Operation ........................................................................................................................ 6
loading and Playing a Cassette Tape........................................................................................................... 6
Loading a Cassette Tape ......................................................................................................................... 6
Playing a Cassette Tape .......................................................................................................................... 6
Dolby Noise Reduction ............................................................................................................................... 6
Special Features ....................................................................................................................... 7
Fast-Forward/Rewind ................................................................................................................................. 7
Pause........................................................................................................................................................... 7
Using Continuous Play ............................................................................................................................... 7
Recording and Dubbing .............................................................................................................................. 8
Recording from Line-In Sources .............................................................................................................. 8
Copying a Cassette Tape (Dubbing) ....................................................................................................... 8
Tape Hints ................................................................................................................................ 9
Restoring Tape Tension and Sound Quality ................................................................................................ 9
Erasing a Cassette Tape .............................................................................................................................. 9
Erase-Protection Tabs ................................................................................................................................. 9
Care and Maintenance ........................................................................................................... 10
Cleaning the Tape-Handling Parts ............................................................................................................ 10
Troubleshooting ..................................................................................................................... 11
Specifications ......................................................................................................................... 13
Index to Features by Control Name ....................................................................................... 14
Notes ...................................................................................................................................... 15
4
PRB1199A.En.01.09.DOC
4
9/2/99, 9:22 PM
CONNECTIONS
CONNECTING THE RECORDING AND
PLAYBACK CABLES
1. Using one of the supplied audio cables,
connect the cassette deck’s left and right LINE
OUTPUT jacks to the receiver/amplifier’s left
and right tape input jacks.
2. Using the other audio cable, connect the
cassette deck’s LINE INPUT jacks to the
receiver/amplifier’s tape output jacks.
Note: If you are not sure which receiver/amplifier jacks to
use, refer to your receiver/amplifier’s owner’s manual.
CONNECTING POWER
Carefully check all connections. Then plug the AC power
cord into a standard AC outlet. The power cord’s plug is
polarized and fits only one way.
Warning: To prevent electric shock, do not plug the
power cord into an extension cord or other receptacle
unless you can fully and easily insert the plug’s blades.
TAPE/ DCC
REC
PLAY
TAPE
2
INPUT
CD
__
L
VCR/
LD
PHONO
REC
PLAY
LINE
OUTPUT
L
R
L
L
INPUT
REC
PLAY
CONTROL
L
R
R
R
R
OUT
RECEIVER/AMPLIFIER
SCT-530
L
L
R
R
L
R
R
L
5
PRB1199A.En.01.09.DOC
5
9/2/99, 9:22 PM
BASIC OPERATION
LOADING AND PLAYING A CASSETTE TAPE
DOLBY NOISE REDUCTION
The Dolby Noise Reduction (NR) system reduces tape hiss
and background noise.
Loading a Cassette Tape
1. Use your finger or a pencil to turn the cassette’s
hub and take up any tape slack.
When you record, the Dolby NR circuit listens to the
program for places where you might later hear tape noise.
The Dolby NR system records these sections at a higher
level. When you play the tape, the circuit decreases the
volume of these sections, restoring the music to its
original level and reducing the level of tape noise.
Note: Do not touch the tape. Fingerprints attract
dust and dirt.
2. Press the appropriate STOP/EJECT button
(Deck l or Deck 2) to open the cassette
compartment door.
Dolby B NR reduces background noise by about 10 dB.
3. Load the cassette with its open edge facing
down and the side you want to play facing
out.
4. Gently close the compartment door.
Note: An index to the cassette deck’s features by
control name is on Page 14. Refer to this index to
find the page where a particular control or indicator
is described.
Playing a Cassette Tape
l. Press POWER to turn on the cassette deck.
2. Set DOLBY HR to IN if the cassette was
recorded with Dolby NR. See “Dolby Noise
Reduction.”
3. Set the receiver/amplifier’s volume control to
its lowest position.
4. Press PLAY for the deck you are using.
5. Adjust the receiver/amplifier’s volume, tone,
and balance controls.
6. Press STOP/EJECT to stop playback.
7. Press STOP/EJECT again to open the cassette
door and remove the cassette.
6
PRB1199A.En.01.09.DOC
6
9/2/99, 9:22 PM
SPECIAL FEATURES
FAST-FORWARD/REWIND
To rapidly advance or rewind the tape, press FAST-F or
REWIND. To stop the tape, press STOP/EJECT. When the
tape reaches the end, the cassette deck automatically
stops.
PAUSE
To temporarily stop playback or recording, press PAUSE.
To restart, press PAUSE again.
Note: You cannot pause while fast-forwarding or
rewinding.
USING CONTINUOUS PLAY
You can load two cassette tapes to play one after the other.
Notes:
•
The cassettes you load should have the same Dolby
NR. type. If they do not, the tape that has a different
Dolby NR. type than the DOLBY NR switch setting
might sound distorted.
•
Be sure to set the tapes properly before starting
continuous play.
1. Load a cassette tape in each tape compartment,
then close the compartment doors.
2. Set DOLBY NR.
3. Press PLAY on Deck 2. The cassette in Deck
2 plays.
4. Adjust the volume, tone, and balance control
on your receiver/amplifier for the desired
sound.
5. Press PAUSE on Deck 1.
6. Press PLAY on Deck 1.
When Deck 2’s cassette tape ends, Deck 2 automatically
stops and Deck 1’s cassette tape plays. When Deck 1’s
cassette tape ends, Deck 1 automatically stops.
7
PRB1199A.En.01.09.DOC
7
9/2/99, 9:22 PM
SPECIAL FEATURES
RECORDING AND DUBBING
Coping a Cassette Tape (Dubbing)
You can record from any component connected to the
receiver/amplifier or dub (copy) cassette tapes.
Notes:
•
If the original recording has Dolby NR, the copy will
also have it, regardless of the position of DOLBY NR.
If the original does not have Dolby NR, you cannot
add it to the tape you are dubbing.
Notes:
•
Tape quality greatly affects the quality of the recording.
Your cassette deck can play Type I and Type II tape. We
recommend Radio Shack brand tapes.
•
Each deck automatically stops when the tape reaches
the end of the side. We recommend you dub onto a
tape that is the same length as the original, so the
decks stop at the same time.
•
Before recording or dubbing, be sure the cassettes onto
which you want to record or dub have their erase-
protection tabs in place. To prevent accidental erasure
of a tape, remove the erase-protection tabs. For more
information, see “Erase-Protection Tabs.”
To copy a cassette tape:
•
To record at the beginning of a cassette, turn the
cassette’s hub with your finger or a pencil until the
dark part of the tape enters the opening in the edge of
the cassette. Before dubbing, position both tapes this
way.
l. Press POWER to turn on the cassette deck.
2. Load the cassette tape you want to copy into
Deck 1. Be sure the side you want to copy is
facing you and the full reel is to the left.
3. Load a blank tape (or one you want to record
over) into Deck 2. Be sure the side you want
to record on is facing you and the full reel is
to the left.
Recording from Line-In Sources
To record from the device connected to the cassette deck’s
LINE INPUT jacks, follow these steps.
4. Set DUBBING SPEED to:
1. Press POWER to turn on the cassette deck.
2. Load a blank tape (or one you want to record
over) into Deck 2. Be sure the side you want
to record on is facing you and the full reel is
to the left.
3. Set DOLBY NR to IN to record with Dolby
Noise Reduction. See “Dolby Noise
Reduction.”
4. Press PAUSE on Deck 2.
5. Press RECORD. PLAY on Deck 2
automatically engages.
6. Play the loudest part of the selection you want
to record.
NORM to dub at normal playback speed.
HIGH to dub at twice the normal speed.
5. Press PAUSE, then PLAY on Deck 1.
6. Press RECORD on Deck 2. PLAY on Deck 2
automatically engages, Deck 1 starts playing,
and dubbing begins.
7. Each deck automatically stops when the tape
reaches the end.
To manually stop dubbing, press STOP/EJECT on both
cassette decks.
If the recording levels constantly peak in the +3 dB
range (or if the recording is distorted), set RECORD
LEVEL ATT to IN. This reduces the input signal level.
7. To begin recording, press PAUSE on Deck 2.
8. To stop recording, press STOP/EJECT on
Deck 2.
8
PRB1199A.En.01.09.DOC
8
9/2/99, 9:22 PM
TAPE HINTS
If you later decide to erase or record over the tape, you
can place a piece of tape over the holes.
RESTORING TAPE TENSION AND SOUND
QUALITY
After you play a cassette tape several times, the tape might
become tightly wound on the reels. This can cause
playback sound quality to deteriorate.
To restore the sound quality, fast-forward the tape from
the beginning to the end of one side, then completely
rewind it. Then loosen the tape reels by gently tapping
each side of the cassette’s outer shell on a flat surface.
Note: When covering the holes, cover only the place that
Note: Be careful not to damage the cassette when tapping
it. Do not touch the exposed tape or allow any sharp
objects near the cassette.
was originally protected by the plastic tab.
ERASING A CASSETTE TAPE
If you no longer want a recording, you can record over it
or erase it.
To record over a cassette tape, simply record as usual. The
cassette deck records over the previous recording.
To erase all or part of a cassette tape, turn off your input
source. Then press RECORD. To erase the entire cassette
tape, let the tape record to the end.
You can quickly erase both sides of a cassette tape using a
bulk tape eraser, available at your local Radio Shack store.
ERASE-PROTECTION TABS
Most cassette tapes have two erase-protection tabs - one
for each side of the tape. When a tab is in place, you can
erase or record on that tape side.
To protect your recordings from being accidentally erased
or recorded over, carefully break off the erase-protection
tabs, using a screwdriver or similar tool.
SIDE A TAB
9
PRB1199A.En.01.09.DOC
9
9/2/99, 9:22 PM
CARE AND MAINTENANCE
Your RCA SCT-530 High-Speed Dubbing Stereo Cassette
Deck is an example of superior design and craftsmanship.
These suggestions will help you care for the cassette deck
so you can enjoy it for years.
Cleaning the Tape-Handling Parts
Clean the tape-handling parts after about every 20 hours
of use. Use a cotton swab dipped in tape head cleaning
solution or denatured alcohol to gently clean the parts
shown in the illustration.
Keep the cassette deck dry. If it gets wet, wipe it
dry immediately. Liquids can contain minerals
that can corrode the electronic circuits.
Capstan
Handle the cassette deck gently and carefully.
Dropping it can damage the circuit boards and
case and can cause the cassette deck to work
improperly.
Erase Head
Pinch Roller
Recording/Playback Head
DECK 2
Use and store the cassette deck only in normal
temperature environments. Temperature
extremes can shorten the life of electronic
devices and distort or melt plastic parts.
Tape head cleaning supplies are available at your
local Radio Shack store.
Keep the cassette deck away from dust and dirt,
which can cause premature wear of parts.
Wipe the cassette deck with a damp cloth
occasionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or strong
detergents to clean the cassette deck.
Modifying or tampering with the cassette deck’s internal
parts can cause a malfunction and might invalidate its
warranty and void your FCC authorization to operate it. If
your cassette deck is not operating as it should, take it to
your local Radio Shack store for assistance.
10
PRB1199A.En.10.16.DOC
10
9/2/99, 9:23 PM
TROUBLE SHOOTING
This cassette deck has been manufactured to the specifications of RadioShack and is covered by a limited warranty from
RadioShack. If your cassette deck is not operating as it should, take it to your local RadioShack store or call 1-800-THE-
SHACK for assistance.
Your cassette deck should give you years of trouble-free service if you follow the instructions in this manual. If you do have
problems, the chart below can help you solve them. If you still have problems after following the suggestions below, take the
cassette deck to your local Radio Shack store for assistance.
Symptom
Cause
Remedy
Power does not come on.
• The power cord is unplugged.
• The component to which the power
cord is attached is turned off.
• Plug in the power cord.
• Turn on the component.
The door does not open.
• The deck is not stopped.
• Power was turned off while the tape
was moving.
• Press STOP/EJECT.
• Turn on the power.
The door does not close.
• The cassette is not properly loaded.
• The tape is at the end of that side.
• The tape has too much slack.
• Remove and reinsert the cassette.
The tape immediately stops.
• Play the other side of the tape or rewind
the tape.
• Take up the slack.
The level meter does not work
during playback.
• There is nothing recorded on the
tape.
• Replace the tape with one that has a
recording.
• The tape heads are dirty.
• Clean the tape heads.
There is no sound.
• The amplifier’s input selector is not
properly set.
• The amplifier’s volume is too low.
• There are connection problems.
• Set the amplifier’s input selector to the
same input you connected the deck to.
• Turn up the amplifier’s volume.
• Check all connections.
The record indicator does not
light when you try to record.
• The erase prevention tabs are broken • Replace the tape with one with unbroken
off.
tabs, or cover the holes with tape.
The level meter does not work
during recording.
• There are connection problems.
• The amplifier is not delivering a
signal to the deck.
• Check all connections.
• Correctly set the amplifier’s controls.
Nothing records onto the tape.
• The tape heads are dirty.
• Clean the tape heads.
The sound is unstable or
interrupted.
• The heads, pinch rollers, or capstans • Clean all tape handling parts.
are dirty.
• The tape is not uniformly wound.
• Completely rewind then fast forward the
tape.
High-frequency sounds are
missing.
• A tape recorded without Dolby NR is • Set DOLBY NR to OUT.
being played back with DOLBY NR
set to IN.
• The tape heads are dirty.
• Clean the tape heads.
11
PRB1199A.En.10.16.DOC
11
9/2/99, 9:23 PM
TROUBLE SHOOTING
Symptom
Cause
Remedy
High-frequency sounds are
emphasized.
• A tape recorded with Dolby NR is
being played back with DOLBY NR
set to OUT.
• Set DOLBY NR to the same position as
was used for recording.
The sounds from previous
recordings are still on the tape
with new recordings.
• The tape heads are dirty.
• Clean the tape heads.
The sound is distorted.
• The recording level is too high.
• The original signal was distorted.
• The heads are dirty.
• Set RECORD LEVEL ATT to IN.
• Replace the original recording source.
• Clean the tape heads.
There is too much noise.
• Poor-quality tape is being used.
• There is a faulty connection.
• The tape heads are dirty.
• Use a better-quality tape.
• Check all connections.
• Clean the tape heads.
12
PRB1199A.En.10.16.DOC
12
9/2/99, 9:23 PM
SPECIFICATIONS
System ............................................................................................................................................ 4-track, 2-channel stereo
Heads.............................................................................................................. One “Hard Permalloy” Record/Playback Head
One “Hard Permalloy” Playback Head
One “Ferrite” Erasing Head
Motor.................................................................................................................................................... One DC Servo Motor
Wow and Flutter ..................................................................................................................................... 0.15% (WRMS, JIS)
Fast Winding Time ............................................................................................................ Approx. 115 seconds (C-60 tape)
Frequency Response (at -20 dB recording level):
Type II (Hi-Bias/Chrome) Tape ............................................................................................................... 30 to 16,000 Hz
Type I (Normal) Tape.............................................................................................................................. 30 to 16,000 Hz
Signal-to-Noise Ratio (Dolby NR Off) ..........................................................................................................More than 56 dB
Noise Reduction Effect:
Dolby B NR ON..................................................................................................................... More than 10 dB (at 5 kHz)
Harmonic Distortion .............................................................................................. No more than 1% (at -4 dB: 160 nwb/m)
Input (Sensitivity) LINE (INPUT) ............................................................................... 112 mV (Input Impedance 24 kOhm)
Output (Reference level) LINE (OUTPUT) .................................................................. 0.5 V (Output Impedance 1.9 kOhm)
Power Requirements ..................................................................................................................................... AC 120V, 60 Hz
Power Consumption ..................................................................................................................................................... 15 W
Dimensions ............................................................................................................................................................................
................................................................................................................................. 5 1/8 x 169/16 x 913/16 Inches (HWD)
130x420x250mm
Weight ...................................................................................................................................................... 7 lbs 8 oz (3.4 kg)
Accessories....................................................................................................................Two connection cords with pin plugs
Specifications are typical ; individual units might vary. Specifications are subject to change and improvement without notice.
13
PRB1199A.En.10.16.DOC
13
9/2/99, 9:23 PM
INDEX TO FEATURES BY CONTROL NAME
This table lists the control and indicator names found on
the front of your cassette deck, along with the page
number where the control or indicator is discussed.
Control/Indicator Name
Page
DOLBY NR
DUBBING SPEED
FAST-F
6
8
7
7
6
6
8
8
7
6
PAUSE
PLAY
POWER
RECORD
RECORD LEVEL ATT
REWIND
STOP/EJECT
14
PRB1199A.En.10.16.DOC
14
9/2/99, 9:23 PM
NOTES
15
PRB1199A.En.10.16.DOC
15
9/2/99, 9:23 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship
under normal use for one (1) year from the date of purchase from RadioShack company-owned stores
and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack
MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS
PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITYTO CUSTOMER
OR ANY OTHER PERSON OR ENTITY WITH RE-SPECT TO ANY LIABILITY, LOSS OR DAMAGE
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES
RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT
OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. In the
event of a product defect during the warranty period, take the product and the RadioShack sales receipt
as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise
provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace
the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts
and products, and products on which a refund is made, become the property of RadioShack. New or
reconditioned parts and products may be used in the performance of warranty service. Repaired or
replaced parts and products are warranted for the remainder of the original warranty period. You will be
charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other
than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or
batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product
removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
09/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
14-1401
<PRB1199-A>
09A99
Printed in
PRB1199A.En.10.16.DOC
16
9/2/99, 9:23 PM
|