M30280T-85LGF
Converter Board for 85-pin 0.65mm pitch TFLGA
User’s Manual
* NQPACK, YQPACK, YQSOCKET, YQ-GUIDE, HQPACK, TQPACK, TQSOCKET, CSSOCKET, CSPLUG/W and LSPACK are
trademarks of Tokyo Eletech Corporation.
Keep safety first in your circuit designs!
ꢀRenesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
Notes regarding these materials
ꢀThese materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
ꢀRenesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
ꢀAll information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
ꢀWhen using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
ꢀRenesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
ꢀThe prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
ꢀIf these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
ꢀPlease contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
Precautions to be taken when using this product
ꢀThis product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
ꢀIn no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
ꢀRenesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
ꢀThis product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
July 16, 2006
(1/4)
REJ10J1450-0100
5. Connection Procedure (See Figure 3)
Emulator
M3028BT-EPB
M30290T-EPB
M3028BT2-CPE
M30290T2-CPE
The procedure for connecting the M30280T-85LGF is outlined
below.
M30280T-85LGF
(2)
(1) Connect the CSSOCKET085B1007RE01 to a foot pattern
on the user system.
M30290T-PTCB
(2) Connect the M30290T-PTCB to the emulator.
(3)
(3) Connect
the
M30280T-85LGF
to
the
CSSOCKET085B1007RE01
(included)
CSSOCKET085B1007RE01.
These corners are not round
85-pin 0.65mm pitch
(PTLG0085JB-A) foot pattern
(1)
A1 pin
User system
Figure 3 Connection procedure of the M30280T-85LGF
6. Height Adjustment (See Figure 4)
If there is a tall peripheral around the place where the
CSSOCKET085B1007RE01 is mounted, the height can be
adjusted about 6mm by using separately available
CSSOCKET085B1007RE01 and CSSOCKET085B1007RE02.
The procedure is outlined below.
M30280T-85LGF
CSSOCKET085B1007RE01
(Separately available)
(3)
(1) Attach the CSSOCKET085B1007RE01 on the user
system to CSSOCKET085B1007RE02 (separately
available).
CSSOCKET085B1007RE02
(Separately available)
(2)
(1)
These corners are not round
CSSOCKET085B1007RE01
(included)
(2) Attach the CSSOCKET085B1007RE02 connected as
above (1) to the CSSOCKET085B1007RE01 (separately
available).
A1 pin
User system
(3) Attach the CSSOCKET085B1007RE01 connected as
above (2) to M30280T-85LGF.
Figure 4
Height adjustment of the M30280T-85LGF and user system
7. Dimensions of M30280-85LGF and Recommended Foot Pattern (See Figure 4)
25.0
5.85
1.30
0.65
4-φ0.8±0.03 (Holes for guide pin)
M30280T-85LGF
REV.A
MADE IN JAPAN
Unit (mm)
85-φ0.35 (Pad diameter)
0.27
Recommended metal mask diameter φ0.35, 0.15 thick
Figure 5 Dimensions of M30280-85LGF and recommended foot pattern
(3/4)
8. Precautions
CAUTION
Note on connecting to the user system
ꢀCaution is demanded, because attaching a converter board in the wrong direction may cause a fatal damage on the
emulator or the user system.
IMPORTANT
Notes on Handling This Product:
ꢀOn the use of this product, prepare recommended foot pattern on the user system, and mount it with recommended
metal mask with diameter (φ0.35mm) and 0.15mm thick.
ꢀCreate a hole for guide pin on the user system where CSSOKET085B1007RE01 is mounted.
ꢀThe following show the recommended reflow conditions (surface temperature) for mounting
CSSOKET085B1007RE01, but the conditions are changed depending on size of the user system, or peripheral.
Lead free solder
Eutectic solder
Pre-heat:
Heat:
Peak:
150 to 180°C, approx. 180sec.
240°C or higher, approx. 30 to 60sec.
260°C
150 to 180°C, approx. 180sec.
210°C or higher, approx. 30 to 60sec.
230°C
Notes on Connectors of the Converter Board:
ꢀThe connectors of the emulator and M30290T-PTCB are guaranteed for up to 50 insertion/removal iterations.
ꢀThe connectors of the M30280T-85LGF and CSSOCKET085B1007RE01 are guaranteed for up to 100
insertion/removal iterations.
Notes on This Product:
ꢀWe cannot accept any request for repair.
ꢀFor purchasing the CSSOCKET085B1007RE01,
LSPACK085B1007RE01, contact the following:
ꢀFor inquiries about the product or the contents of this manual, contact your local distributor.
the
CSSOCKET085B1007RE02
and
the
Renesas Tools Homepage
(4/4)
|